Grilled Tomahawk Steak
This impressive piece of beef would be right at home on The Flintstones! Taken from the rib area, tomahawk steak is super-thick with a distinctive long bone. A big cut like this is all about simplicity and sharing: Serve it on a wooden board, separate out the bone and slice it into strips so everyone can help themselves.
Preparation - 5 min
Cooking - 20 min
Waiting - 1 hour
Servings - 4
Ingredients
Preparation
Citation
Ricardocuisine. (n.d.). Our 10 most popular BBQ recipes | RICARDO. Ricardo. https://www.ricardocuisine.com/en/articles/top-rated-recipes/979-our-10-most-popular-bbq-recipes
Inquires Answered
Burners Will Not Light
1. Turn off Grill and any gas supply. LP Tank must be turned off and removed from regulator.
2.Connect the gas supply back in to the LP tank or turn on Nat Gas (This will reset the saftey device in the regulator)
3. Turn on all burners on high for 10 Secounds. Then turn back off. (this primes gas to the burners to make sure the supply reaches)
4. Turn on again and the grill will fire up. (you are ready to grill)
IF THE GRILL STILL WILL NOT START OR FIRE UP.
you will manually start it with a Log lighter to test See instructions.
5. Follow steps 1 and 2
6. Follow step 3 and use Log Lighter on burner to see if it lights up.
7. If it lights up you will need to see the Ignighter/Valve trouble shooting on the FAQ
8. If it still does not light. you do not have gas comming to the grill. You will need to contact a Licenced Gas Plumber to diagnose why you dont have gas comming to the grill.
Rotisserie Kit Assembley
Fire Coming out of Control Panel and Knobs
Burners need to be Cleaned and Valves need to be replaced.
Something is disturbing the gas flow. When burners are clogged or wind pushes the flame back into the control pannel you will get Back Flash and this will melt down the bushings in your control valves and create a small leak.
You will need to check and replace.
See Replacement Part
Do you hook up the gas lines
We do hook up Liquid Propane (LP) Gas Lines with a LP Regulator that will hook up to a small gas tank supplied by the customer.
If you have Natural Gas you will need to contact a Local Licenced Plumber to set this up.
Main Ignitors Do Not Work On My Grill
1. Make sure all Valves are turned off
2. Discounect LP tank or turn off the Natural Gas Valve
3. Reconnect your LP tank or turn on your Natural Gas Valve
How to test your Ignitors to see if they are working
4. Use a (Log Lighter) to Manually Start your Grill to see if you can get it lit.
5. If it lights using a lighter the Ignitor is bad and will need to be replaced.
6. Check each Ignitor / Control Knob to see how many need to be replaced.
7. See attached Video on how to replace Valves
YOUR BURNERS STILL DO NOT WORK?
8. You are not getting gas to the grill
9. Call Licensed Plumber
Do you need new Valve/Ignitor? See replacment parts
How to Clean Briquettes / How to clean Grill
1. Turn over all Briquettes over burner so the greasy side faces down.
2. Turn Grill on High Baking it off, then turn off the grill and let cool.
3. Wash Briquettes with Dawn soap water and scratch pad
4. Rinse and let briquettes dry before next use.
Note: See Replacments parts to replace with new
HOW TO CLEAN GRILL
5. Dawn Soap water and wipe down grill and all parts.
6. Let dry and use.
How to Connect Side Burner & Grill to Natural Gas
Contact a licence Plumber or a professional qualified Craftsman to run any gas lines and hook up.
CAUTION: USE YELLOW TEFLON TAPE ON ALL CONNECTIONS!
USE SOAP WATER ON CONNECTONS TO TEST LINES FOR LEAKS AFTER. IF YOU SEE BUBBLES YOU HAVE A LEAK!
1. Use 1 3/8 Stainlees Steel Flare Fitting Gas Lines to hook up to Side Burner
2. Use another 3/8 Stainless Steel Flare Fittiing Gas Line to hook up to Grill.
3. Use a 3 way 3/8" Flare fitting and connect one hose from side burner and the other from grill.
5. Connect 1 more 3/8" Stainless steel Flex lines to the last side on the 3 way and connect to your gas supply.
6. CHECK ALL YOUR WORK WITH SOAP WATER.
7. SPRAY ALL CONNECTING JOINTS THEN TURN ON GAS GRILL AND SIDE BURNER AND MAKE SURE THEY ARE LIT.
8. LOOK FOR BUBBLES IN YOUR LINES. IF YOU SEE BUBBLES YOU HAVE A GAS LEAK.
IF YOU DONT SEE ANY YOU ARE SAFE.
How to Convert Grill Gas types LP or NG
Convert your gas grill. See Video Instructions
See Parts you will need replacement parts
How to Install & Light My Sear Burner
See Video Instuctions
How to Light the Back Burner on BBQ Grill
1. Make sure your gas supply is turned on
2. Push and hold the back Burner knob (RED KNOB) for 10 secounds.
3. Then turn the Knob until you hear it click
4. Repeat until back burner lights.
WHAT IF IT CONTINUES?
5. Check spark at the back burner area (two metal prongs at the back burner area)
6. Make sure they spark when turning the knob.
7. They need to have a spark
8. Carfully move the two prongs closer togather and follow steps starting at step 5